Location:
Self-adhesive polymer-modified bitumen waterproofing membrane
Self-adhesive polymer-modified bitumen waterproofing membrane
  • Self-adhesive polymer-modified bitumen waterproofing membrane
  • 1/1
  • Self-adhesive polymer-modified bitumen waterproofing membrane

Self-adhesive polymer-modified bitumen waterproofing membrane

share
Facebook
X
LinkedIn
Pinterest
Whatsapp
Tumblr
Self-adhesive polymer-modified bitumen waterproofing membrane (hereinafter referred to as Type N) uses SBS and other synthetic rubbers, premium road asphalt, and tackifiers as its base materials. The upper surface material consists of polyester film (PET), polyethylene film (PE), aluminum foil, or a silicon-coated release film, while the lower surface is coated with a silicon-coated release film as an anti-adhesion layer. This forms a self-adhesive polymer-modified bitumen waterproofing membrane without a reinforcing base.
Send E-mail
Get A Quote
Detail

Product Overview

Self-adhesive polymer modified bituminous waterproofing membrane (hereinafter referred to as Type N) uses synthetic rubber such as SBS, high-quality road asphalt and tackifier as the base material. It is a self-adhesive polymer modified bituminous waterproofing membrane made with polyester film (PET), polyethylene film (PE), aluminum foil or silicon-coated release film as the surface material, and the lower surface covered with a silicon-coated release film as the bonding layer.

Self-adhesive polymer modified bituminous polyester tire waterproofing membrane (hereinafter referred to as Type PY) uses long-fiber polyester felt as the tire base, self-adhesive polymer modified asphalt as the impregnating and coating material, with the upper surface covered with polyethylene film, fine sand, aluminum foil, self-adhesive polymer modified asphalt or silicon-coated release film as the isolation layer, and the lower surface coated with self-adhesive asphalt or silicon-coated release film.

Wide-width self-adhesive pre-laid polyester tire waterproofing membrane (hereinafter referred to as pre-laid Type PY) uses the coating material of the waterproofing membrane as the main material (forming a self-adhesive waterproof layer), with both sides coated with peelable silicon-coated release films as isolation materials to make a functional waterproofing membrane.

Wide-width self-adhesive polymer pre-laid waterproofing membrane (hereinafter referred to as pre-laid Type P) uses ethylene-vinyl acetate (EVA) and high-density polyethylene (HDPE) homogeneous sheets as the main materials, with the surface coated with a self-adhesive layer and then covered with a silicon-coated release film to make a polymer self-adhesive waterproofing membrane. According to engineering needs, geotextiles can be compounded on the polymer sheet to strengthen the strength of the membrane. The reinforced tire waterproofing membrane uses asphalt-based polyester tire waterproofing membrane as the main material (with functional additives added), coated with a self-adhesive layer on one or both sides, and can use a peelable silicon-coated film as the isolation material to make a wet-laid waterproofing membrane.

Product Classification

Tire BaseUpper Surface MaterialProduct PerformanceThicknessWidthArea
Without tire base (Type N)Polyethylene film (PE)Type Ⅰ1.2mm1000mm10m²
15m²
20m²
30m²
Polyester film (PET)1.5mm
Film-free double-sided self-adhesive (D)Type Ⅱ2.0mm
Polyester tire base (Type PY)Polyethylene film (PE)Type Ⅰ2.0mm
Fine sand surface (S)Type Ⅱ3.0mm
Film-free double-sided self-adhesive (D)4.0mm
Self-adhesive Polymer Modified Bituminous Waterproofing Membrane   Complies with GB23441-2009 Standard   Main Physical and Mechanical Properties of Type N
Serial NumberItemⅠⅡD


PEPETPEPET
1Tensile strength (N/50mm) ≥150200200150-
Elongation at maximum tensile strength (%) ≥250-30200-
Heat resistance   Elongation (%) ≥-250-150450
2Heat resistanceNo separation between the coating layer and the tire body before the specified fracture during stretching
3Nail rod tear strength (N) ≥601107040-
4Low-temperature flexibility (℃)-20-30-30-20-20
5Water impermeability (30min)0.2Mpa, impermeable for 120min
6Membrane to membrane (N/mm) ≥1.0
Membrane to base (N/mm) ≥1.5
7Resistance to static water pressure (MPa) ≥0.3
8Holding power (min) ≥20
9Tensile strength retention rate (%) ≥80
Elongation retention rate at maximum tensile strength (%) ≥80
10Low-temperature flexibility (℃)-18-28-18-28-18
Heat aging   Maximum tensile strength retention rate (%) ≥80
Elongation retention rate (%) ≥30 (Type D is 400% elongation of asphalt coating layer)
11Thermal stabilityNo wrinkling, lack of adhesive, flowing, sliding
12Self-adhesive asphalt re-peeling strength (N/mm) ≥1.51.01.51.0
Main Physical and Mechanical Properties of Type PY
Serial NumberItemIndex


ⅡⅠ
1Soluble content (g/m²) ≥2.0mm1300-
3.0mm2100-
4.0mm2900-
2Tensile performance2.0mm350600
3.0mm450-
4.0mm550-
Elongation at maximum tensile strength (%) ≥3080
3Heat resistanceNo sliding, flowing, dripping at 70℃
4Low-temperature flexibility (℃)-20-30
5Water impermeability0.3Mpa, impermeable for 30min
6Peeling strength (N/mm) ≥Membrane to membrane1.01.5
Membrane to plate1.5-
7Resistance to static water pressure (MPa) ≥0.3
8Holding power (min) ≥20
9Heat agingTensile strength retention rate (%) ≥8080
Elongation retention rate at maximum tensile strength (%) ≥3040
Low-temperature flexibility (℃)-18-28
10Thermal stabilityAppearanceNo wrinkling, lack of adhesive
Maximum slip (mm) ≤2
11Self-adhesive asphalt re-peeling strength (N/mm) ≥1.51.0

Application Scope

  • Waterproofing of non-exposed roofs and underground projects;
  • Waterproofing of municipal projects such as fruit pools and swimming pools;
  • Waterproofing of open-cut subway projects;
  • Especially suitable for waterproofing projects where open flames cannot be used;
  • Excellent low-temperature performance, suitable for use in cold regions.
contact us
WeChat Official Account
Follow us