Location:
Two-component polyurethane waterproof coating

Two-component polyurethane waterproof coating

share
Facebook
X
LinkedIn
Pinterest
Whatsapp
Tumblr
Two-component polyurethane waterproof coating is a chemically cured waterproofing material. Component A consists of an isocyanate-terminated prepolymer obtained through the polycondensation of polyether and isocyanate. Component B is a colored liquid comprising plasticizers, curing agents, thickeners, accelerators, and fillers. During application, components A and B are thoroughly mixed in the specified ratio. The mixture is then applied to the waterproofing substrate surface. It undergoes cross-linking and curing at room temperature, forming a rubber-like elastic coating that provides waterproofing protection.
Send E-mail
Get A Quote
Detail

Product Overview

Two-component polyurethane waterproof coating is a two-component chemical reaction curing type waterproof material. Component A is a prepolymer terminated with isocyanate obtained by the condensation polymerization of polyether and isocyanate. Component B is a colored uniform liquid composed of plasticizer, curing agent, thickener, accelerator, and filler. When in use, mix components A and B in proportion evenly, apply them on the surface of the base layer, and form an elastic rubber-like waterproof film through chemical reaction to play a waterproof role.

Construction Method

  • Requirements for the base layer: The surface of the base layer should be solid and flat. When using cement mortar for leveling, it must be fully cured without looseness, sanding, or peeling. It should meet the design requirements.
  • The treatment of wet surfaces should be in accordance with the design, instructions for use, and treatment requirements.
  • The moisture content of the construction surface should not be greater than 15%.
  • After the base layer is cleaned, key parts such as internal and external corners, expansion joints, and construction joints should be treated.
  • For key parts such as deformation joints, prime coat should be applied in proportion according to the construction requirements to improve the bonding strength and sealing effect.
  • After the prime coat is dry, the waterproof coating can be applied by brushing or spraying.
  • If the waterproof layer has special design requirements, a fiber-reinforced layer can also be laid according to the design requirements. Before brushing, methods such as spreading coarse sand and other aggregates on the surface of the waterproof layer must be adopted to make its surface rough to facilitate subsequent construction.
  • Requirements for the base layer: The base layer should be dry, flat, and free of debris. Uneven areas and deformation cracks in the base layer must be leveled with cement mortar. Pipes, sanitary facilities, floor drains, etc. connected to the base layer must be installed firmly with tight joints, smooth ends, and no looseness.
  • The first coat should be applied in a consistent direction. After the first coat is cured for 12-24 hours, apply the second coat. Generally, the second coat is perpendicular to the first coat, and the 2nd-3rd coats follow. Brushing or spraying can be used. To increase the bonding force between the waterproof layer and the rigid protective layer, fine sand is often spread on the surface when it is not fully cured, and after initial curing, the floating sand on the surface is removed before constructing the rigid protective layer.
  • Treatment of detailed structures: Additional waterproof layers should be applied to details such as internal and external corners, pipe roots, cracks, and deformation joints.
  • According to the construction requirements, the film construction can also be completed in one coat, and after curing, the protective layer construction can be carried out.

Performance Indicators

Two-component polyurethane waterproof coating complies with GB/T19250-2013, main physical and mechanical properties

Serial NumberItemTechnical Indicators


ⅠⅡⅢ
1Solid content (%) Multi-component ≥92.0
2Surface drying time (h) ≤12
3Actual drying time (h) ≤24
4Leveling propertyNo obvious flowing after 20min
5Tensile strength (MPa) ≥2.006.0012.0
6Elongation at break (%) ≥500450250
7Tear strength (N/mm) ≥153040
8Low-temperature flexibility-35℃, no cracks
9Water impermeability0.3MPa, 120min, impermeable

One-component polyurethane waterproof coating complies with GB/T19250-2013, main physical and mechanical properties

Serial NumberItemTechnical Indicators


ⅠⅡⅢ
1Solid content (%) Single-component ≥85.0
2Surface drying time (h) ≤12
3Actual drying time (h) ≤24
4Leveling propertyNo obvious flowing after 20min
5Tensile strength (MPa) ≥2.006.0012.0
6Elongation at break (%) ≥500450250
7Tear strength (N/mm) ≥153040
8Low-temperature flexibility-35℃, no cracks
9Water impermeability0.3MPa, 120min, impermeable
10Heating shrinkage rate (%) ≤-4.0~+1.0

Product Features

  • The single-component can be directly constructed on the surface of the wet base layer, with fast construction speed, which can shorten the construction period.
  • High strength, high elongation, high elastic recovery rate, and strong adaptability to base layer cracking.
  • Excellent low-temperature flexibility.
  • The coating is dense, without pinholes, bubbles, and has a small water vapor permeability coefficient. It can not only be waterproof but also water vapor proof. The color can be adjusted to meet the personalized requirements of different customers for surface colors.
  • One coating can reach a thickness of 1-3mm without forming [missing content, assumed to be "cracks" or similar].
  • Two-component coatings form a seamless and complete elastic waterproof layer through cement hydration and curing. Its film has high strength and extensibility, which cannot be achieved by waterproof rolls, especially having the adaptability that the film can extend with the cracking of the waterproof base layer and elastic substrate base layer.
  • It adheres firmly to the base layer. The waterproof coating has good adhesion to concrete, wood, metal, ceramics, stone, and other high polymers, and can also be used as a bonding layer.
  • Two-component (A and B) polyurethane coating is a cold-construction waterproof coating. During construction, it is only necessary to mix components A and B in proportion and apply them on the waterproof base layer.
  • Local repair of easily leaking detailed structure parts can still achieve the original waterproof effect, saving time, labor, and cost.
  • It is an environmentally friendly product with little odor, reducing harm to people and the environment, and is an ideal tar-based substitute material.
contact us
WeChat Official Account
Follow us